Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 30 of 8760
CURRENT
2017-12-11
Standard
AMS2451/4D
This specification establishes the requirements for brush plating of cadmium by electrodeposition.
2017-12-08
WIP Standard
AMS4330C
This specification covers an aluminum alloy in the form of plate.
2017-12-08
WIP Standard
AMS4306C
This specification covers an aluminum alloy in the form of plate.
CURRENT
2017-12-07
Standard
AMS4434N
This specification covers a magnesium alloy in the form of sand castings.
CURRENT
2017-12-07
Standard
AMS4958E
This specification covers a titanium alloy in the form of bars and rods 1.00 inch (25.4 mm) and under in nominal diameter.
CURRENT
2017-12-07
Standard
AMS5532H
This specification covers a corrosion and heat-resistant iron alloy in the form of sheet, strip, and plate.
CURRENT
2017-12-07
Standard
AMSQQA200/6C
This specification covers the specific requirements for aluminum alloy 5454 bar, rod, shapes, tube, and wire produced by extrusion.
CURRENT
2017-12-07
Standard
AMSQQA200/7C
This specification covers the specific requirements for aluminum alloy 5456 bar, rod, shapes, tube, and wire produced by extrusion.
CURRENT
2017-12-07
Standard
AMS4035M
This specification covers an aluminum alloy in the form of sheet and plate 0.010 to 1.750 inch (0.25 to 44.45 mm) in thickness, supplied in the annealed (O temper) condition (see 8.4). When specified, product shall be supplied in the “as fabricated” (F) temper.
CURRENT
2017-12-07
Standard
AMS5350K
This specification covers a corrosion and moderate heat-resistant steel in the form of investment castings.
CURRENT
2017-12-07
Standard
AMS4928W
This specification covers a titanium alloy in the form of bars, wire, forgings, flash welded rings, drawn shapes up through 10.000 inches (254.00 mm) inclusive in diameter or least distance between parallel sides and stock of any size for forging or flash welded rings.
CURRENT
2017-12-07
Standard
AMS5537J
This specification covers a corrosion and heat-resistant cobalt alloy in the form of sheet, strip, foil, and plate up to 2.250 inches (57.15 mm) inclusive, in nominal thickness (see 8.4).
CURRENT
2017-12-07
Standard
AMS6931D
This specification covers a titanium alloy in the form of bars and forgings up through 10.000 inches (254.00. mm), inclusive, in diameter or least distance between parallel sides with a maximum cross-sectional area of 79.0 in2 (506.45 cm2) and forging stock of any size (see 8.7).
CURRENT
2017-12-05
Standard
AMS6466G

This specification covers a corrosion-resistant steel in the form of welding wire.

2017-12-03
WIP Standard
AMSQQA200/5B
This specification covers the specific requirements for aluminum alloy 5086 bar, rod, shapes, tube, and wire produced by extrusion.
2017-12-03
WIP Standard
AMSQQA225C
This specification covers the general requirements for aluminum and aluminum alloy bar, rod, wire, or special shapes; rolled, drawn, or cold finished. Specific requirements for these products are covered by the applicable detail specification (See 6.3).
2017-12-03
WIP Standard
AMSQQA200/13C
This specification covers the specific requirements for aluminum alloy 7178 bar, rod, shapes, tube, and wire produced by extrusion.
2017-12-03
WIP Standard
AMSQQA200/14B
This specification covers the specific requirements for aluminum alloy 7178-T76 bar, rod, shapes, and wire produced by extrusion.
2017-11-30
WIP Standard
AMS03_18A
This SAE Standard specifies the properties of chromate conversion coatings on aluminum and aluminum alloys. It details inspection and testing requirements for chromate conversion coatings. Where there are differences in the requirements for the Brushing Grade from the Standard Grade they are highlighted in this Standard.
CURRENT
2017-11-30
Standard
AMS4268A
This specification covers an aluminum alloy in the form of sheet and plate 0.010 to 1.500 inch (0.254 to 38.07 mm), inclusive, in thickness, supplied in the -T81/-T851 temper (see 8.5).
2017-11-27
WIP Standard
AMS6952
This specification covers a titnaium alloy in the form of forgings 4.4 inches (111.76 mm) and under in nominal diameter or least distance between parallel sides and forging stock of any size.
CURRENT
2017-11-21
Standard
AMS4916L
This specification covers a titanium alloy in the form of sheet, strip, and plate up through 4.000 inches (101.60 mm) inclusive in thickness (see 8.6).
CURRENT
2017-11-20
Standard
AMS2451/11B
This specification covers the requirements for brush plating of cobalt by electrodeposition.
CURRENT
2017-11-20
Standard
AMS6951
This specification covers a titanium alloy in the form of sheet 0.025 through 0.100 inches (0.63 through 2.54 mm) inclusive in thickness (see 8.5).
CURRENT
2017-11-20
Standard
AMSQQA200/4C
This specification covers the specific requirements for aluminum alloy 5083 bar, rod, shapes, tube, and wire produced by extrusion.
2017-11-17
WIP Standard
J125
The purpose of this SAE Information Report is to provide automotive engineers and designers with a concise statement of the basic characteristics of cast iron under elevated temperature conditions. As such, the report concentrates on general statements regarding these properties with limited illustrative data, anticipating that those who may be interested in more detail will want to use the bibliography provided at the conclusion of the report.
2017-11-17
WIP Standard
J1434
This report approaches the material selection process from the designer's viewpoint. Information is presented in a format designed to guide the user through a series of decision-making steps. "Applications criteria" along with engineering and manufacturing data are emphasized to enable the merits of aluminum for specific applications to be evaluated and the appropriate alloys and tempers to be chosen.
2017-11-17
WIP Standard
J417
This report lists approximate hardness conversion values; test methods for Vickers Hardness, Brinell Hardness, Rockwell Hardness, Rockwell Superficial Hardness, Shore Hardness; and information regarding surface preparation, specimen thickness, effect of curved surfaces, and recommendations for Rockwell surface hardness testing for case hardened parts.
2017-11-17
WIP Standard
J419
This report covers the recommended practice for the evaluation and measurement of decarburization in ferrous material. Included are definitions of types with charts and micrographs and methods most commonly used for the measurement of decarburization.
Viewing 1 to 30 of 8760