Criteria

Text:
Display:

Results

Viewing 1 to 30 of 1135
2017-09-19
Technical Paper
2017-01-2142
Brandon Mahoney, Jamie Marshall, Thomas Black, Dennis Moxley
It is well recognized that weight savings within an airframe can result in significant lifetime cost savings and increased flight range. The transition of aluminum alloys to lighter, composite materials is an increasingly prevalent strategy to reduce weight on aircraft. This paper describes the application of a lightweight carbon fiber composite technology to aviation, engine start lithium batteries. The transition of lithium battery chassis technology from metal to composite introduces technical challenges not found with traditional battery chassis. Modern lithium batteries contain more than energy cells; common internal components include switch mode battery chargers, health and safety monitoring electronics, and even environmental control circuitry such as heaters. Consequently, electromagnetic interference disruption potential created by the electronics must be addressed.
2017-09-19
Technical Paper
2017-01-2028
Steven Nolan, Patrick Norman, Graeme Burt, Catherine Jones
Turbo-electric distributed propulsion (TeDP) for aircraft allows for the complete redesign of the airframe so that greater overall fuel and emissions benefits can be achieved. Whilst conventional electrical power systems may be used for smaller aircraft, much larger aircraft are likely to require the use of superconducting electrical power systems to enable the required whole system power density and efficiency levels to be achieved. The TeDP concept requires an effective electrical fault management and protection system. However, the fault response of a superconducting TeDP power system and its components has not been well studied to date, limiting the effective capture of associated protection requirements. For example, with superconducting systems it is the possible that a hotspot is formed on one of the components, such as a cable. This can result in one subsection, rather than all, of a cable quenching.
2017-09-19
Technical Paper
2017-01-2024
Natasha L. Schatzman, Narayanan Komerath, Ethan A. Romander
The crossing event of the blades of a coaxial counter-rotating rotor is a potential source of noise and severe blade loads. Blade crossings occur several times each rotor revolution. Most of the radial variation in the flow field can be efficiently captured by stacking the results of a 2-D analysis using two airfoils approaching each other at the appropriate relative Mach number and separation distance. Previously, this phenomenon was analyzed by simulating two airfoils passing each other at specified speeds and vertical separation distances, using the compressible Navier-Stokes solver OVERFLOW. The simulations explored thickness, circulation, and compressible effects. Results revealed the complex nature of the aerodynamic and fluid dynamic impulses generated by blade-blade interactions, with implications for aeroelastic loads and aeroacoustic sources.
2017-07-10
Technical Paper
2017-28-1947
Suresh Kumar Kandreegula, Kamal Rohilla, Naveen Sukumar, Kunal Kamal
Abstract A propeller shaft is a mechanical component of drive train that connects transmission to drive wheels/axle with the goal to transfer rotation and torque. It is used when the direct connection between transmission and drive axle is not possible due to large distance between their respective assigned design spaces. In commercial vehicles especially in heavy duty (GVW/GCW>15 tons) a single piece propeller shaft is seldom used due to its inherent disadvantages and therefore, most if not all, of the setups consists of multiple pieces of propeller shaft which are directly mounted on to frame cross members with the help of mounting brackets. As such the mounting bracket assembly undergoes various dynamic and static loading conditions and should be able to withstand these loads. This paper will focus on the FEA analysis of propeller shaft mounting assembly system.
2017-07-10
Technical Paper
2017-28-1949
Johnson Jose, Ramesh M, G Venkatesan, M Khader Basha
Abstract Unmanned Aerial Vehicles (UAV) are being deployed in military, law enforcement, search & rescue, scientific research, environmental & climate studies, reconnaissance and other commercial and non-commercial applications on a large scale. A design and development of landing gear system has been taken up for a UAV. This paper presents the design optimization of structural components of Wheel-Brake & Fork assembly pertaining to the Main Landing Gear (MLG) for a UAV. The wheel, fork, axle and brake unit constitute the wheel assembly. The wheel-brake assembly is assembled with the strut assembly and forms the Landing gear system. The Fork is the connecting member between the shock strut and the axle containing the wheel-brake assembly. As the fork and axle are subjected to shock loads while landing, the strength of these components are very much essential to withstand the dynamic loads.
2017-06-05
Journal Article
2017-01-1765
Albert Allen, Noah Schiller, Jerry Rouse
Abstract Corrugated-core sandwich structures with integrated acoustic resonator arrays have been of recent interest for launch vehicle noise control applications. Previous tests and analyses have demonstrated the ability of this concept to increase sound absorption and reduce sound transmission at low frequencies. However, commercial aircraft manufacturers often require fibrous or foam blanket treatments for broadband noise control and thermal insulation. Consequently, it is of interest to further explore the noise control benefit and trade-offs of structurally integrated resonators when combined with various degrees of blanket noise treatment in an aircraft-representative cylindrical fuselage system. In this study, numerical models were developed to predict the effect of broadband and multi-tone structurally integrated resonator arrays on the interior noise level of cylindrical vibroacoustic systems.
2017-06-05
Technical Paper
2017-01-1775
Mark A. Gehringer, Robert Considine, David Schankin
Abstract This paper describes recently developed test methods and instrumentation to address the specific noise and vibration measurement challenges posed by large-diameter single-piece tubular aluminum propeller (prop) shafts with high modal density. The prop shaft application described in this paper is a light duty truck, although the methods described are applicable to any rotating shaft with similar dynamic properties. To provide a practical example of the newly developed methods and instrumentation, impact FRF data were acquired in-situ for two typical prop shafts of significantly different diameter, in both rotating and stationary conditions. The example data exhibit features that are uniquely characteristic of large diameter single-piece tubular shafts with high modal density, including the particular effect of shaft rotation on the measurements.
2017-03-28
Technical Paper
2017-01-1592
Jingdong Cai, Saurabh Kapoor, Tushita Sikder, Yuping He
Abstract In this research, active aerodynamic wings are investigated using numerical simulation in order to improve vehicle handling performance under emergency scenarios, such as tight cornering maneuvers at high speeds. Air foils are selected and analyzed to determine the basic geometric features of aerodynamic wings. Built upon the airfoil analysis, the 3-D aerodynamic wing model is developed. Then, the virtual aerodynamic wings are assembled with the 3-D vehicle model. The resulting 3-D geometry model is used for aerodynamic analysis based on numerical simulation using a computational fluid dynamics (CFD) software package. The CFD-based simulation data and the vehicle dynamic model generated are combined to study the effects of active aerodynamic wings on handling performance of high-speed vehicles. The systematic numerical simulation method and achieved results may provide design guidance for the development of active aerodynamic wings for high-speed road vehicles.
2016-10-25
Technical Paper
2016-36-0511
Wilcker Neuwald Schinestzki, Daniel Gustavo Schreiner, Carlos Eduardo Guex Falcão
Abstract The drag reduction system, commonly used in Formula 1, has as task to reduce the drag force that acts in the vehicle’s airfoils, increasing considerably its speed. When it comes to Formula SAE competition, since the speeds are lower than in F1, the purpose of the DRS can easily become the cooling, despite its name. This paper comes to the development of a drag reduction system applied to the frontal wing whose major objective is to increase the mass flow rate of air through the radiator. Based on a preliminary work supported by computational fluid dynamics, a frontal wing DRS can increase the mass flow rate in approximately 65% at an average velocity of 12 meters per second, which allows the team to use a smaller and lightweight radiator. The challenge was to design a lightweight and reliable automatic system, since it cannot fail nor take away the driver’s attention.
2016-09-27
Technical Paper
2016-01-2103
Eric Barton
This technical paper details an optimized Drivmatic machine design delivered to a Tier 1 aero structure supplier to automate drilling and installation of rivets, hi-loks, lockbolts & swage collars for individual fuselage panel assemblies with high throughput & strict quality requirements. While certain robot solutions continue to be explored for specific applications at many Tier 1 aero structure suppliers, robot payload capacity has limitations beyond certain criteria, which often times point towards an alternative machine design as in this case study. A typical approach for adding more automation is to allocate shop floor space based on the solution’s foot print, however contrary to most approaches this solution had to be designed to fit within a pre-determined factory footprint over a geographic location with a high water table that would not permit a foundation.
2016-09-27
Technical Paper
2016-01-2105
Thomas G. Jefferson, Richard Crossley, Anthony Smith, Svetan Ratchev
Abstract This paper presents novel development of a reconfigurable assembly cell which assembles multiple aerostructure products. Most aerostructure assembly systems are designed to produce one variant only. For multiple variants, each assembly typically has a dedicated assembly cell, despite most assemblies requiring a process of drilling and fastening to similar tolerances. Assembly systems that produce more than one variant do exist but have long changeover or involve extensive retrofitting. Quick assembly of multiple products using one assembly system offers significant cost savings from reductions in capital expenditure and lead time. Recent trends advocate Reconfigurable Assembly Systems (RAS) as a solution; designed to have exactly the functionality necessary to produce a group of similar components. A state-of-the-art review finds significant benefits in deploying RAS for a group of aerostructures variants.
2016-09-27
Technical Paper
2016-01-2095
Agata Suwala, Lucy Agyepong, Andrew Silcox
Abstract Reduction of overall drag to improve aircraft performance has always been one of the goals for aircraft manufacturers. One of the key contributors to decreasing drag is achieving laminar flow on a large proportion of the wing. Laminar flow requires parts to be manufactured and assembled within tighter tolerance bands than current build processes. Drilling of aircraft wings to the tolerances demanded by laminar flow requires machines with the stiffness and accuracy of a CNC machine while having the flexibility and envelope of an articulated arm. This paper describes the development and evaluation of high accuracy automated processes to enable the assembly of a one-off innovative laminar flow wing concept. This project is a continuation of a previously published SAE paper related to the development of advanced thermally stable and lightweight assembly fixture required to maintain laminar flow tolerances.
2016-09-27
Journal Article
2016-01-2112
Hilmar Apmann
Abstract As a new material FML, made by aluminum foils and Glasfiber-Prepreg, is a real alternative to common materials for fuselages of aircrafts like monolithic aluminum or CFRP. Since experiences within A380 this material has some really good advantages and develops to the status as alternative to aluminum and composite structures. To become FML as a real alternative to aluminum and carbon structures there are many things to improve: design, material, costs and process chain. So following one of the main goals for an industrial application for high production rates of aircrafts is the automation of production processes inside the process chain for FML-parts like skins and panels for fuselages. To reach this goal for high production rates first steps of automation inside this new process chain have been developed in the last two years. Main steps is the automated lay-up of metallic foils and Glasfiber-Prepreg.
2016-09-27
Technical Paper
2016-01-2124
Sara Nilsson, Jonas Jensen, Mats Björkman, Erik Sundin
Abstract Carbon fiber-reinforced plastic (CFRP) is one of the most commonly used materials in the aerospace industry today. CFRP in pre-impregnated form is an anisotropic material whose properties can be controlled to a high level by the designer. Sometimes, these properties make the material hard to predict with regards to how the geometry affects manufacturing aspects. This paper describes eleven design rules originating from different guidelines that describe geometrical design choices and deals with manufacturability problems that are connected to them, why they are connected and how they can be minimized or avoided. Examples of design choices dealt with in the rules include double curvature shapes, assembly of uncured CFRP components and access for non-destructive testing (NDT). To verify the technical content and ensure practicability, the rules were developed by, inter alia, studying literature and performing case studies at SAAB Aerostructures.
2016-09-27
Journal Article
2016-01-2120
David Judt, Kevin Forster, Helen Lockett, Craig Lawson, Philip Webb
Abstract In the civil aircraft industry there is a continuous drive to increase the aircraft production rate, particularly for single aisle aircraft where there is a large backlog of orders. One of the bottlenecks is the wing assembly process which is largely manual due to the complexity of the task and the limited accessibility. The presented work describes a general wing build approach for both structure and systems equipping operations. A modified build philosophy is then proposed, concerned with large component pre-equipping, such as skins, spars or ribs. The approach benefits from an offloading of the systems equipping phase and allowing for higher flexibility to organize the pre-equipping stations as separate entities from the overall production line. Its application is presented in the context of an industrial project focused on selecting feasible system candidates for a fixed wing design, based on assembly consideration risks for tooling, interference and access.
2016-09-27
Technical Paper
2016-01-2133
Carl Landau
Abstract Aircraft manufacturers are seeking automated systems capable of positioning large structural components with a positional accuracy of ±0.25mm. Previous attempts at using coordinated arm robots for such applications have suffered from the use of low accuracy robots and minimal systems integration. Electroimpact has designed a system that leverages our patented Accurate Robot technology to create an extensively automated and comprehensively integrated process driven by the native airplane component geometry. The predominantly auto-generated programs are executed on a single Siemens CNC that controls two Electroimpact-enhanced Kuka 6 axis robots. This paper documents the system design including the specification, applicable technologies, descriptions of system components, and the comprehensive system integration. The first use of this system will be the accurate assembly of production empennage panels for the Boeing 777X, 787 and 777 airplanes.
2016-09-27
Technical Paper
2016-01-2130
Enkhsaikhan Boldsaikhan, Shintaro fukada, Mitsuo Fujimoto, Kenichi Kamimuki, Hideki Okada, Brent Duncan, Phuonghanh Bui, Michael Yeshiambel, Brian Brown, Alan Handyside
Abstract The Refill Friction Spot Joining (RFSJ) is an emerging solid-state spot welding technology that thermo-mechanically creates a molecular-level bond between the work-pieces. RFSJ does not consume any filler or foreign materials so that no additional weight is introduced to the assembly. As the solid-to-liquid phase transition is not involved in RFSJ in general, there is no lack of fusion or material deterioration caused by liquefaction and solidification. Unlike the conventional friction stir spot welding, RFSJ produces a spot joint with a perfectly flush surface finish without a key or exit hole. Currently, the aerospace industry employs solid rivets for fastening the primary structures as they meet the baseline requirements and have well-established standards and specifications.
2016-09-27
Journal Article
2016-01-2139
Hendrik Susemihl, Christian Moeller, Simon Kothe, Hans Christian Schmidt, Nihar Shah, Christoph Brillinger, Jörg Wollnack, Wolfgang Hintze
Abstract A mobile robotic system is presented as a new approach for machining applications of large aircraft components. Huge and heavy workshop machines are commonly used for components with large dimensions. The system presented in this paper consists of a standard serial robot kinematics and a mobile platform as well as a stereo camera system for optical measurements. Investigations of the entire system show that the mechanical design of the mobile platform has no significant influence on the machining accuracy. With mobile machines referencing becomes an important issue. This paper introduces an optical method for determining the position of the mobile platform in relation to the component and shows its accuracy limits. Furthermore, a method for increasing the absolute accuracy of the robots end-effector with help of stereo camera vision is presented.
2016-09-27
Technical Paper
2016-01-2089
Jose Guerra cEng, Miguel Angel Castillo
Abstract Aernnova experience on automatic drilling operations started in 1,999. The company signed a new contract with Embraer, to design, manufacture and assembly several structures of the model 170. It was big news for the company. But after that minute of pride, manufacturing engineering people of the company started to think about the process to assemble those big panels of the Horizontal Stabilizer, Vertical Stabilizer and Rear Fuselages in the best Quality and Cost. There were a lot of rows of rivets to install. Some ideas arisen, but the final decision was to forget the available processes at that time and think about to automate the drilling, countersink and riveting of the stringers, doublers and window frames to the panels. There were a lot of doubts, figures to do and obstacles, but the company took the decision of going ahead with that process. That step changed the state of the art at that time in the company.
2016-09-27
Technical Paper
2016-01-2090
Sergey Lupuleac, Margarita Petukhova, Julia Shinder, Alexander Smirnov, Mariia Stefanova, Nadezhda Zaitseva, Tatiana Pogarskaia, Elodie Bonhomme
Abstract The paper is devoted to description of features and functionalities of special software complex aimed at global simulation of junction process using efficient numerical algorithms. The paper presents the concept of developed software and its structure. Types of problems, which the complex is applicable for, are enumerated.
2016-09-20
Technical Paper
2016-01-2055
Koji Muraoka, Daisuke Hirabayashi, Masayuki Sato, Yoshihisa Aoki
Abstract JAXA (Japan Aerospace Exploration Agency) has been conducting a research on a future commercial tilt wing VTOL (Vertical TakeOff and Landing) transport under JAXA's "Sky Frontier" Program aiming to develop technologies for aircraft innovation. The research focuses on QTW (Quad Tilt Wing) civil VTOL transport, which features tandem tilt wings with propellers mounted at the mid-span of each wing. The goals of the research in the present phase are to propose a concept of a QTW business VTOL transport system and to pursue the essential technologies development such as OEI (One-Engine-Inoperative) safe recovery, transition flight control and cruise efficient aerodynamic design. Nine passengers business QTW concept was designed and trade-off analysis of the propulsion system architecture for OEI safety was conducted.
2016-09-20
Technical Paper
2016-01-2046
Neno Novakovic
Abstract A Landing Gear Control and Actuation System (LGCAS) is one of the most complex aircraft systems. Due to the large landing gear masses and high performance requirements, aircraft hydraulic power with multiple hydraulic actuators and valves is used to provide system dynamic. LGCAS also requires a electrical source of energy for the electro-mechanical components, sensors and electronic control unit. For many years, correct fault isolation in a complex kinematic system, such as an aircraft landing gear actuation system, has been a great challenge with limited success. The fault isolation design challenge rests on the fact that landing gear control and actuation system has many so called “passive” components, whose basic function cannot be continuously monitored without additional sensors, transducers, and designated health monitoring equipment.
2016-09-20
Technical Paper
2016-01-1979
William D. Bertelsen
Abstract Technology to create a VTOL for general aviation that is fast, efficient, easy to fly, and affordable, has proven elusive. Bertelsen Design LLC has built a large research model to investigate the potential of the arc wing VTOL to fulfill these attributes. The aircraft that is the subject of this paper weighs approximately 145 kg (320 lbs) and features coaxial, dual-rotating propellers, diameter 1.91 m (75 inches). Power is from an MZ 202 two-cycle, two-cylinder engine. Wingspan is 1.82 m (72 inches). The arc wing differentiates this aircraft from previous deflected-slipstream prototypes, which suffered from pitch-trim issues during transition. This paper will present configuration details of the Bertelsen model, showing how it is possible to generate high lift from a short-span wing system. The Bertelsen model can hover out of ground effect using just two arc-wing elements: a main wing and a “slat”.
2016-09-20
Journal Article
2016-01-2013
Evgeni Ganev, Chiyuan Chiang, Leroy Fizer, Ed Johnson
Abstract This paper addresses the implementation of electric taxiing without the use of main engines by using electric propulsion of the landing gears. Substantial progress in this area has been achieved by Honeywell Aerospace and Safran in a joint initiative for developing an electric green taxiing system (eTaxi). Considerable analysis, design, fabrication, and testing have already been completed, which culminated in a demonstration at the Paris Air Show (PAS) in 2013. The eTaxi system has been installed on an A320 airplane that uses the auxiliary power unit (APU) to generate electric power to provide propulsion to two wheels of the main landing gear. The main advantages of such a system are reduction of fuel consumption and audio noise, reduction of CO2 , carbon and nitrous emissions, reduced engine foreign object damage (FOD) exposure and fast-turn time savings by elimination of the ground tractor for pushback operation.
2016-09-20
Technical Paper
2016-01-2019
Richard P. Johnston
Abstract An advanced composite Blended Wing Body (BWB) air frame previously used as a study aircraft to transport a 75-ton military cargo halfway around the world and back unrefueled has been modified and evaluated as a 150-ton heavy lifter. The modifications include enlarging the forward trim canard, reducing fuel load by 151,850 lbs, increasing the high-mach NASA-type counter-rotating propellers from 12 feet to 13 feet diameter, extending the propeller support pylons' height by 6 inches and modifying cruise flight and prop control strategies. Due to structural and propulsion system changes, the air frame Operational Empty Weight (OEW) was increased by 1,850 lbs. but the maximum Take Off Gross Weight (TOGW) was held to 800,000 lbs. Brief descriptions of the major propulsion system components are provided. In addition, a comparison of three different counter-rotating propeller systems is presented. The first is a Standard configuration.
2015-09-15
Technical Paper
2015-01-2402
Yucheng Liu
Abstract Differential equations play a prominent role in aerospace engineering by modeling aerospace structures, describing important phenomena, and simulating mathematical behavior of aerospace dynamical systems. Presently, aerospace systems have become more complex, space vehicle missions require more hours of simulation time to complete a maneuver, and high-performance missiles require more logical decisions in there phases of flight. Because of these conditions, a computationally efficient algorithm for solving these differential equations is highly demanded to significantly reduce the computing time.
2015-09-15
Technical Paper
2015-01-2577
Alessandro Ceruti, Piergiovanni Marzocca, Vitaly Voloshin
Abstract The aim of this paper is to develop a new concept of unconventional airship based on morphing a lenticular shape while preserving the volumetric dimension. Lenticular shape is known to have relatively poor aerodynamic characteristics. It is also well known to have poor static and dynamic stability after the certain critical speed. The new shape presented in this paper is obtained by extending one and reducing the other direction of the original lenticular shape. The volume is kept constant through the morphing process. To improve the airship performance, four steps of morphing, starting from the lenticular shape, were obtained and compared in terms of aerodynamic characteristics, including drag, lift and pitching moment, and stability characteristics for two different operational scenarios. The comparison of the stability was carried out based on necessary deflection angle of the part of tail surface.
2015-09-15
Technical Paper
2015-01-2578
Alessandro Ceruti, Piergiovanni Marzocca
Abstract The flight simulation of airships and hot air balloons usually considers the envelope geometry as a fixed shape, whose volume is eventually reduced by ballonets. However, the dynamic pressure or helium leaks in airships, and the release of air to allow descent in hot air balloons can significantly change the shape of the envelope leading to potential dangerous situations. In fact, in case of semi-rigid and non-rigid airships a reduction in envelope internal pressure can reduce the envelope bending stiffness leading to the loss of the typical axial-symmetric shape. For hot air balloons thing goes even worse since the lost of internal pressure can lead to the collapsing of the balloon shape to a sort of vertically stretched geometry (similar to a torch) which is not able to sustain the attached basket and its payload.
2015-09-15
Technical Paper
2015-01-2615
Donald Jasurda
The aerospace industry is continually becoming more competitive. With an aircraft's large number of components, and the large supplier base used to fabricate these components, it can be a daunting task to manage the quality status of all parts in an accurate, timely and actionable manner. This paper focuses on a proof of concept for an aircraft fuselage assembly to monitor the process capability of machined parts at an aircraft original equipment manufacturer (OEM) and their supply chain. Through the use of standardized measurement plans and statistical analysis of the measured output, the paper will illustrate how stakeholders can understand the process performance details at a workcell level, as well as overall line and plant performance in real time. This ideal process begins in the product engineering phase using simulation to analyze the tolerance specifications and assembly process strategy, with one of the outputs being a production measurement plan.
2015-09-15
Technical Paper
2015-01-2614
Hideki Okada, Kenichi Kamimuki, Syuhei Yoshikawa, Shintaro Fukada
In the modern aircraft manufacturing, the cost reduction, the manufacturing time reduction, and the weight saving of aircraft are strongly demanded. The Refill Friction Spot Joining [1,2](FSJ, in other words FSSW, Friction Stir Spot Welding), which is one of innovative solid-state joining methodologies based on the Friction Stir Welding[3], is a promising technology that can replace rivets and fasteners. This technology is expected to offer cost reduction and weight saving for the aircraft manufacturing. In this study, to make stronger and reliable joints, the shoulder-plunging process of Refill FSJ was employed. The weldability of the Alodine or Chromic Acid Anodize coated materials along with a faying-surface sealant was investigated. The joint properties, such as tensile shear strengths and corrosion resistance, were evaluated.
Viewing 1 to 30 of 1135