Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 206
2017-04-02
WIP Standard
J974
This SAE Standard covers the general requirements and the test requirements for a flashing warning lamp for agricultural equipment.
CURRENT
2017-01-06
Standard
J167_201701
This SAE Standard applies to an overhead cover installed on a protective frame or enclosure conforming to SAE J2194 or alternately SAE J1194 and the following additional requirement of a drop test to verify the effectiveness of the overhead cover in protecting the operator from falling objects. The test procedures and performance requirements outlined in this document are based on currently available engineering data.
2016-12-07
WIP Standard
J983
This SAE Recommended Practice applies to mobile, construction type, crane and cable excavator hand and foot controls. It should not be construed to limit the use of, or to apply to combination controls, automatic controls, or any other special operating control requirements.
CURRENT
2016-11-28
Standard
J2194_201611
Any ROPS meeting the performance requirement of ISO 5700 (Static ROPS Test Standard) or ISO 3463 (Dynamic ROPS Test Standard) meets the performance requirements of this SAE Standard if the ROPS temperature/material and seat belt requirements of this document are also met.
CURRENT
2016-11-23
Standard
J1194_201611
Fulfillment of the intended purpose requires testing as follows:
2016-09-27
WIP Standard
J717
This SAE Standard establishes specifications for mid- and side-power take-off drives that will be helpful in designing implements. Design of the implement attaching means must be tailored to each tractor, depending on attaching points available and the exact location of the auxiliary shaft.
CURRENT
2016-08-02
Standard
J284_201608
This SAE Recommended Practice covers the safety alert symbol intended for use on construction and industrial equipment as defined in SAE J1116 and on agricultural tractors and machinery as defined in ASABE S390.
2016-03-25
WIP Standard
J712
The purpose of this SAE Recommended Practice is to provide a selection of disc wheels for industrial and agricultural application with a maximum of interchangeability. This is accomplished by establishing five groups of disc wheels, in each of which the hub mounting elements are common. These groups are designated 4 bolt, 5 in bolt circle; 5 bolt, 4.5 in bolt circle; 5 bolt, 5.5 in bolt circle; 6 bolt, 6 in bolt circle; and 8 bolt, 8 in bolt circle. Further, this document establishes an SAE part number and the maximum rated radial load for each standard wheel. In addition, the document requires the wheel manufacturer's name or trademark to be impression stamped on the wheel with location at the discretion of the manufacturer.
CURRENT
2015-09-22
Standard
J1939/74_201509
The SAE J1939 documents are intended for light, medium, and heavy-duty vehicles used on or off road as well as appropriate stationary applications which use vehicle derived components (e.g. generator sets). Vehicles of interest include, but are not limited to, on- and off-highway trucks and their trailers, construction equipment, and agricultural equipment and implements. The purpose of these documents is to provide an open interconnect system for electronic systems. It is the intention of these documents to allow Electronic Control Units to communicate with each other by providing a standard architecture. This particular document, SAE J1939-74, describes the message structure for a set of messages which enable the user to determine and announce to others on the network, the parameter placement within a particular message from the special set of messages defined within this document.
CURRENT
2015-03-27
Standard
J397_201503
This SAE Standard applies to operator protective structures which may commonly be a part of construction, forestry, mining, and industrial machines.
CURRENT
2015-03-27
Standard
J1254_201503
This SAE Standard includes names of major components and parts peculiar to this type of machine. Illustrations used here are not intended to include all existing commercial machines or be exactly descriptive of any particular machine. They have been provided to describe the principles to be used in applying this document.
CURRENT
2015-03-17
Standard
J2970_201503
This standard provides the testing and functional requirements guidance necessary for a leak detection device that uses any non-A/C refrigerant tracer gas, such as helium or a nitrogen-hydrogen blend, to provide functional performance equivalent to a refrigerant electronic leak detector. It explains how a non- refrigerant leak detector’s calibration can be established to provide levels of detection equal to electronic leak detectors that meet SAE J2791 for R-134a and SAE J2913 for R-1234yf.
CURRENT
2014-10-24
Standard
J67_201410
This SAE Standard applies to all machines with shovel, clam, or dragline attachment.
CURRENT
2014-10-21
Standard
J2417_201410
This SAE Standard provides a uniform method to calculate the lift capacity of knuckle-boom log loaders and certain forestry equipment. It establishes definitions and specifies machine conditions for calculations. This document applies to knuckle-boom log loaders as defined in ISO 6814 and ISO 17591 and certain forestry equipment defined in ISO 6814 that have a rotating upper-structure such as feller bunchers, forwarders, harvesters, and behind the cab or rear-mounted knuckle-boom log loaders not having their own power supply. It does not apply to harvesters that are incapable of lifting a tree or log completely off the ground. This document applies to those machines that are crawler, rubber-tired, and pedestal or stationary mounted.
2013-06-28
WIP Standard
J1305
The purpose of this SAE Recommended Practice is to establish the minimum performance requirements of devices which signal and/or automatically prevent two-blocking. This SAE Recommended practice applies to cranes in lifting crane service which are equipped with two-block warning and/or limit systems.
2013-06-28
WIP Standard
J1332
The purpose of this recommended practice is to establish the minimum performance requirements for devices used to indicate to the crane operator by visual, audible, or tactile means the movement of a rope drum. This SAE Recommended Practice applies to cranes when used in lifting crane service which are equipped with rope drum rotation indicating devices.
CURRENT
2013-06-17
Standard
J1063_201306
This SAE Standard applies to mobile, construction-type lifting cranes of the cantilever boom type (Figure 1). Questions and comments regarding application or interpretation of the provisions in this test method should be referred to the originating SAE Committee.1
CURRENT
2013-04-18
Standard
J881_201304
This SAE Standard covers minimum dimensional relationship for sheaves, drums, and wire rope for mobile, construction type lift cranes.
CURRENT
2013-03-28
Standard
J1289_201303
To establish conditions to be taken into consideration in determining rated loads for mobile cranes when overturning stability is the controlling factor. This recommended practice applies to mobile, construction-type lifting cranes with either lattice booms or cantilevered, telescopic booms.
2013-03-19
WIP Standard
J1078
This analysis applies to crane types as covered by Power crane and shovel Association Standard Number Two, Mobile Hydraulic Crane standards and ANSI B30.15; refer to 5.1. This calculation method has been established to illustrate an analysis to determine the competence of hydraulic telescopic cantilevered crane booms.
CURRENT
2013-01-02
Standard
J1116_201301
This SAE Standard applies to self-propelled off-road work machines. Included are the following categories: Earthmoving Implements and Attachments Forestry Road Building and Maintenance Specialized Mining Powered Industrial Trucks This SAE Standard does not apply to Agricultural Tractors as defined in ANSI/ASAE S390 although some SAE standards are also applicable to Agricultural Tractors. NOTE: Most standards relating to agricultural tractors and implements are developed by ASABE.
CURRENT
2012-08-20
Standard
J987_201208
This SAE Standard applies to mobile construction-type lifting cranes utilizing rope-supported, conventional and luffing type lattice boom crane structures.
CURRENT
2012-06-04
Standard
J959_201206
This SAE Standard applies to all mobile, construction-type, lifting cranes as equipped for operation with hook, clamshell, magnet, and grapple attachments. It is not applicable to excavating and demolition attachments such as shovels, hoes, draglines, and wrecking balls. The purpose of this document is to set forth wire-rope strength factors that have been proved by design and operating practice to be consistent with safety, economy, space, weight, and other requirements peculiar to mobile, construction-type, lifting cranes.
CURRENT
2012-05-02
Standard
J375_201205
This SAE Recommended Practice applies to cranes used in lifting-crane service which are equipped with radius-of-load or boom angle indicating devices.
CURRENT
2012-05-02
Standard
J376_201205
This SAE Recommended Practice applies to cranes equipped with load indicating devices used in lifting crane service.
CURRENT
2012-05-02
Standard
J1180_201205
This SAE Recommended Practice applies to mobile cranes when used in lifting crane service which are equipped with boom length indicating devices.
2012-03-06
WIP Standard
J159
This SAE Standard applies to cranes when used in lifting service that are equipped with Rated Capacity Systems. Purpose The purpose of this document is to establish the minimum performance and tolerance criteria of systems used to warn or to indicate to the operator and/or other responsible persons when the load being lifted approaches, meets and exceeds the rated capacity on the applicable rated capacity chart of the crane.
CURRENT
2012-02-21
Standard
J1257_201202
This recommended practice applies to mobile construction type cranes with cantilevered, telescopic booms when used in lifting crane service.
CURRENT
2012-02-06
Standard
J958_201202
This SAE Standard includes names of major components and parts peculiar to this type of equipment. The illustrations are not intended to show all existing commercial machines or to be exactly descriptive of any particular machine. They have been selected to depict principles used in identifying specific mechanisms and to identify useful dimensional relationships.
CURRENT
2012-02-06
Standard
J220_201202
This SAE Recommended Practice applies to the boomstop for the main boom of all mobile construction type cranes having rope supported booms, equipped for hook work, clamshell, magnet, grapple, or concrete bucket attachments.
Viewing 1 to 30 of 206

Filter

  • Standard
    206